Weston 08-3201-W Manual de Instruções descarregar pdf (Página 11)

NEVER operate Grinder without the

Tray secured in place.

To avoid serious or fatal injury, NEVER reach

into any Grinder inlet.

ALWAYS use the Stomper to push meat

into the Grinder Head.

Read & fully understand all instructions

& warnings prior to use.

WARNING!

1. Follow the “Grinder Assembly

Instructions” to fully assemble the

Grinder including the Tray.

NOTE: It is best to grind the meat

using the coarse, 7 mm Grinding

Plate rst. If a ner grind of meat is

desired, run the coarse ground meat

through the Grinder a second time

using the ne, 4.5 mm Grinding

Plate.

2. Trim the meat of all cords,

tendons, bones, shot, etc.

3. For best results, be sure that all meat

has been chilled to between 32-34

F (0-1

before grinding. DO NOT ALLOW MEAT

TO SIT OUT AT ROOM TEMPERATURE

LONGER THAN ABSOLUTELY NEEDED.

Closely follow the “Food Safety” instructions

as outlined by the USDA.

4. Cut meat into sizes small enough to t into

the Feed Chute. Approximately 1” (2.5 cm)

cubes.

5. Place cubed meat to be ground into the

Tray. Do not overll the Tray, place just

enough meat to leave the Feed Chute area

open.

6. Place a dish or bowl to collect the ground

meat at the end of the Grinder Head

(Figure 5).

7. Make sure the Grinder is in the “OFF”

position. Attach the Grinder to the power

supply.

8. Switch the Grinder to the forward “FWD”

position. Carefully start feeding cubes of

meat into the Feed Chute. ONLY USE THE

STOMPER TO PUSH MEAT INTO THE

HEAD, DO NOT USE YOUR FINGERS OR

ANY OTHER OBJECT.

WARNING! The Tray helps protect the user

from serious personal injury. ALWAYS use

the Stomper to feed and push meat into the

Grinder.

GRINDING INSTRUCTIONS

WARNING! Before cleaning, assembling or disassembling the Grinder,

make sure the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

ALWAYS unplug the Grinder when not in use.

FIGURE 5

Tray

Stomper

Grinder

Head

Bowl for

ground meat

WARNING! Before cleaning, assembling or disassembling the Grinder,

make sure the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

ALWAYS unplug the Grinder when not in use.

HIGH-SPEED STUFFER

ASSEMBLY INSTRUCTIONS

NOTE: The High-Speed Stufng System

is designed for use with the 10 mm Funnel

ONLY. DO NOT attempt to use the High-

Speed Plastic Auger with any other Funnels.

SERIOUS DAMAGE to the Grinder Head

and other components may occur. Follow

the “Standard Stuffer Assembly Instructions”

located in this manual, when using the 20, 30,

or 40 mm Funnels.

1. Insert the Head into the Gear Housing

with the feed chute of the Head facing straight

up. You will need to line up the slot in the

Head with the Pin inside the Gear Housing.

Be sure the Head is seated fully into the Gear

Housing

(Figure 10).

2. Tighten the Head Locking Knob to

lock the Head into place.

3. Insert the Auger, with the Auger

Bearing attached, into the Head

(Figure 11).

Align the Auger Splines with the Drive

Shaft of the Grinder.

NOTE: Periodically inspect the

Auger Bearing for wear. If the

Auger Bearing is worn excessively,

replace it immediately or Head

damage could result.

4. Slide the High Speed Plastic

Auger onto the Auger Pin making

sure the square part of the Plastic

Auger fully seats on to the square

portion of the Auger Pin.

5. Slide the 10 mm Stufng

Funnel through the through the

Flange and place it through the

Front Ring Nut.

6. Install the Front Ring Nut,

DO NOT OVERTIGHTEN. Turn

the Front Ring Nut until it makes

contact with the Flange, then

make 1/4 turn more to tighten into

place.

...INSTRUCTIONS CONTINUED

ON NEXT PAGE

FIGURE 10

FIGURE 11

Head

Auger Bearing

Auger

Auger Splines

Auger Pin

High-Speed

Plastic Auger

Front Ring

Nut

Flange

-11-

-14-

The Gear Housing and the Motor Cover

may become HOT during operation. This is

normal. DO NOT touch these parts during

operation or until they cool after use.

HOT

DO NO T T OUCH!

Motor

Cover

Feed

Chute

Gear

Housing

NEVER operate Grinder without the

Tray secured in place.

To avoid serious or fatal injury, NEVER reach

into any Grinder inlet.

ALWAYS use the Stomper to push meat

into the Grinder Head.

Read & fully understand all instructions

& warnings prior to use.

WARNING!

Gear

Housing

Head

Slot in Head

Head Locking

Knob

Feed

Chute

1 2 ... 6 7 8 9 10 11 12

Comentários a estes Manuais

Sem comentários

Weston 08-3201-W Manual de Instruções Página 11

Comentários a estes Manuais

Manuais e produtos relacionados com Picadoras Weston 08-3201-W